I Hate Dialysis Message Board
Welcome, Guest. Please login or register.
November 22, 2024, 12:14:07 PM

Login with username, password and session length
Search:     Advanced search
532606 Posts in 33561 Topics by 12678 Members
Latest Member: astrobridge
* Home Help Search Login Register
+  I Hate Dialysis Message Board
|-+  Off-Topic
| |-+  Off-Topic: Talk about anything you want.
| | |-+  It's never, ever like the manual
0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: It's never, ever like the manual  (Read 1825 times)
RightSide
Elite Member
*****
Offline Offline

Gender: Male
Posts: 1117


« on: January 18, 2012, 02:51:23 PM »

After 2 1/2 years of faithful service, the heat sink in my computer started to fail (fan noisy, temperatures rising) and needed to be replaced.  So I got a replacement heat sink and prepared to install it this past Saturday.

I'd read the instruction manual that came with it, as well as the manual that came with my motherboard.  Replacing the heatsink looked like a straightforward job.  And the heat sink only cost about $45, so the job looked inexpensive too.

Well, it wasn't either straightforward or inexpensive.

Even though I was being careful and gentle, when I started removing the old heat sink, the CPU remained stuck to the bottom of it.  (When they call that stuff "thermal paste," they're not kidding.)  When I lifted the heat sink, it pulled the CPU right out of its motherboard socket despite being locked in place there.  Old thermal paste (which is nonconductive) oozed onto the CPU pins.  I couldn't think of any way to get it off.  That was the end of the CPU--and my only means to access the Internet.

Now how to order a replacement CPU?  Newegg.com and Amazon.com won't take telephone orders.  TigerDirect.com does, but I had to pay more than Newegg or Amazon charges. That set me back $150.  And I had to wait for it to be shipped and delivered.

So I only got everything back together about five hours ago--and a job that should have gone quickly and cheaply cost me $200 and 4 days to complete.

Just out of curiosity, I phoned Best Buy and talked with their "Geek Squad" about how this had gone so wrong.  They told me that thermal paste (used to affix the heat sink to the CPU for a heat-conductive bond) can dry out after a couple of years of continuous use of the computer, making it more likely that the CPU will stick to the heat sink and be difficult to pull apart.  They suggested that I reapply fresh thermal paste every year.

None of the manuals I read had mentioned that little fact.
Logged
MooseMom
Member for Life
******
Offline Offline

Gender: Female
Posts: 11325


« Reply #1 on: January 18, 2012, 02:58:28 PM »

I have never heard of  "heat sink".

I have heard the term "motherboard", but I don't know what it is.

I don't know what "CPU" means.

I've never heard of "thermal paste".

 :P
Logged

"Eggs are so inadequate, don't you think?  I mean, they ought to be able to become anything, but instead you always get a chicken.  Or a duck.  Or whatever they're programmed to be.  You never get anything interesting, like regret, or the middle of last week."
cattlekid
Elite Member
*****
Offline Offline

Gender: Female
Posts: 1269

« Reply #2 on: January 18, 2012, 03:38:12 PM »

Wow.  I can't believe that the Geek Squad even knew what thermal paste was, much less suggested that it be freshened every year.  But then again, it's been so long since I stuck my hands inside a computer.  I built one back in the mid 90's but that was it.  Now, I take the cheap and easy route.
Logged
sullidog
Elite Member
*****
Offline Offline

Gender: Male
Posts: 1432

« Reply #3 on: January 18, 2012, 04:41:30 PM »

It's a good idea every year to also open up the tower and clean and blow all the dust and grime out of it.
Logged

May 13, 2009, went to urgent care with shortness of breath
May 19, 2009, went to doctor for severe nausea
May 20, 2009, admited to hospital for kidney failure
May 20, 2009, started dialysis with a groin cath
May 25, 2009, permacath was placed
august 24, 2009, was suppose to have access placement but instead was admited to hospital for low potassium
august 25, 2009, access placement
January 16, 2010 thrombectomy was done on access
Pages: [1] Go Up Print 
« previous next »
 

Powered by MySQL Powered by PHP SMF 2.0.17 | SMF © 2019, Simple Machines | Terms and Policies Valid XHTML 1.0! Valid CSS!